Sonic-alert Digital Program Controller DCP301 Manuale Utente Pagina 140
- Pagina / 187
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 8. PROGRAM SETUP
8-13
■ Inserting and deleting segments
(1) In the setting display state, move to the pattern item of the segment where the seg-
ment is to be inserted or deleted on the programming map.
(2) If you press
FUNC
+
ENT
, the display changes to confirm insertion of the segment,
and “I N S .” is displayed blinking in the upper display.
(3) If you press , the display changes to confirm insertion of the segment, and “I N S .”
is displayed blinking in the upper display.
If you press , the display changes to confirm deletion of the segment, and “D E L .”
is displayed blinking in the upper display.
(4) If you press
ENT
while “I N S .” is displayed on the upper display, the segment is
inserted.
If you press
ENT
while “D E L .” is displayed on the upper display, the segment is
deleted.
(5) The DCP301 returns to the setting display state.
● Display (inserting segment)
● Display (deleting segment)
• When you insert a segment, a new segment is automatically created at the currently
displayed segment No., and all segment Nos. onward are incremented by one. The
setting of the inserted segment is as follows:
SP setting value: Same value as original segment before the new segment was in serted
Time setting value: 0:10
Events, time events and G.Soak are not set, and the PID set No. is set to 0.
• If you try to insert a segment in a program already containing 30 segments, pressing
ENT
will not insert the segment.
• When you delete a segment, the next segment shifts down to the currently displayed
segment No. and subsequent segment Nos. are decremented by one.
When you delete the last segment, the display changes to “- - - -” indicating that noth-
ing is set.
• Segments cannot be inserted or deleted from currently running (RUN, HOLD, FAST,
END) programs.
Program No. Segment No.
Pattern
tendency
EV1 to EV3 and T1 to T5 all out
I N S.
Program No. Segment No.
Pattern
tendency
EV1 to EV3 and T1 to T5 all out
D E L
.
- Digital Program Controller 1
- User’s Manual 1
- WARRANTY 2
- TECHNICAL ASSISTANCE 2
- SAFETY PRECAUTIONS 3
- Unpacking 6
- Contents 8
- Chapter 7. PARAMETER SETUP 10
- Chapter 8. PROGRAM SETUP 10
- Chapter 9. TROUBLESHOOTING 11
- Chapter 10 12
- SPECIFICATIONS 12
- Chapter 11. CALIBRATION 12
- RUN/HOLD 13
- 1-1 Features 14
- 1-2 Basic Function Blocks 15
- 1-3 Data Structure 16
- 1-4 System Configuration 17
- 1-5 Model Numbers 18
- 2-1 Structure 19
- 2-2 Console 20
- Basic display state 22
- ■ Loader jack 25
- 2-3 Input Type and Range No 26
- Chapter 3. MOUNTING 28
- 3-2 Panel Cutout Dimensions 29
- 3-3 Mounting 30
- ■ Dust-proof cover 31
- ■ Mounting method 32
- 4-1 Wiring Precautions 33
- 4-2 Compensating Lead 35
- 4-3 Terminal Connections 36
- Direction 37
- ■ Power supply 38
- ■ Ground 38
- Chapter 4. WIRING 39
- ■ Connecting input 1 40
- ■ RS-485 interface 48
- Digital circuit 51
- 5-1 Data 52
- 5-2 Program Patterns 53
- ■ Events 1 to 3 54
- Chapter 5. FUNCTIONS 55
- ■ Time events 1 to 5 57
- ■ G.Soak (guarantee soak) 59
- ■ PID set selection 59
- (1)' 60
- (1)" 60
- ■ Pattern link 61
- 5-3 Modes 62
- ■ Mode transition 64
- ■ Mode transition operations 65
- ■ Mode transition limitations 66
- 5-4 Controller and Programmer 67
- ■ Control output 69
- ● 2G output 71
- ● 3D, 5K outputs 72
- MANUAL mode 72
- ■ SP output 73
- ■ Auxiliary output 73
- 6-1 Turning the Power ON 74
- Chapter 6. OPERATION 75
- Motor valve opening (%) 79
- Output state of events 1 to 3 79
- 6-3 Program Selection 80
- ■ Program selection 82
- ■ Read timing 83
- ■ Manual operation 84
- ■ Auto-tuning (AT) 84
- 7-1 Parameter Setup 86
- 7-2 How to Use 89
- 7-3 Parameter Setup List 92
- Handling Precautions 100
- E T 1 0 103
- E D 1 0 103
- H Y S 1 5 103
- D L 1 0 103
- PID Set No. Designated in the 108
- Program or Zone No. According 108
- ■ Setup data settings “S E t” 112
- SSR' 120
- q 0 (Special functions) 122
- Short-circuit 123
- ■ Table data settings “T B L” 125
- MV upper limit (CH1) 127
- I N S .” blinking 129
- d E L .” blinking 129
- C L R .” blinking 129
- ■ Programming map 131
- ■ Setting up pattern items 132
- ■ Display details 132
- Program No. Segment No 133
- ■ Setting up PV start items 138
- ■ Setting up cycle items 138
- P.L I N 139
- Program No 141
- Copy destination program No 141
- G .R E S 142
- ■ Alarm code display 144
- ■ Alarm categories 144
- 9-4 Replacing the Battery 152
- Comes out towards you 153
- Key cover 153
- Lock screw 153
- Connector 154
- RAM board 154
- (approx. 3cm x 8cm) 154
- Gray holder 155
- 10-1 Specifications 156
- Chapter 10. SPECIFICATIONS 157
- 25 ) and 157
- Item Specification 157
- ■ Accessories/option list 162
- 10-2 External Dimensions 163
- Chapter 11. CALIBRATION 166
- 4.0.4.4 169
- 2.0.2.2 169
- 11-2 Calibration Procedures 170
- ■Function test 171
- 1.0.1.1 174
- Table 11-11 175
- ■Current output calibration 176
- 11-3 Set Up 177
- Programming Map 179
- SAFETY REQUIREMENTS 180
- Revision History 184
- HONEYWELL SERVICE CENTERS 185
- No. CP-UM-5093E 187
Prodotti e manuali riguardandi Orologio Sonic-alert Digital Program Controller DCP301
Orologio Sonic-alert SB200ss Manuale Utente
(2 pagine)
(2 pagine)
Orologio Sonic-alert SBP100 Manuale Utente
(2 pagine)
(2 pagine)
Orologio Sonic-alert SB300SS Manuale Utente
(2 pagine)
(2 pagine)
Formax FD 8500HS podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Niszczarki Formax FD 8500HS.
Dostarczamy 1 pdf podręczników Formax FD 8500HS do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commenti su questo manuale